ACTFLEX 600 PRIMER Hybrid
The primer under ACTFLEX 906 WPU. One coat, touch dry in 20 minutes, membrane on the same day.
ACTFLEX 600 PRIMER is a one-component, moisture-cured hybrid polyurethane primer built for ACTFLEX 906 WPU. It cures on air moisture like a solvent PU, yet takes the water-based 906 WPU straight over the cured film. 4 L and 17 L.
Where to use it
- Under ACTFLEX 906 WPU water-based polyurethane membrane
- New and aged concrete, rendered surfaces and masonry
- Compressed fibrous cement sheeting
- Precast concrete panels and smooth factory-finished surfaces
- Existing waterproofing layers, for intercoat bonding in repairs
Why waterproofers buy it
- The specified bonding primer for ACTFLEX 906 WPU
- Moisture cured, yet directly overcoatable with water-based membranes
- Touch dry in approx. 20 minutes, waterproof in 3 hours, full cure in 6 hours. Membrane on the same day
- One coat at 50 to 100 microns. Roller, brush or spray
- 10 year Forspec product warranty
Coverage
4 to 6 m² per litre. 4 L: approx. 16 to 24 m². 17 L: approx. 68 to 102 m². Use the whole tin the same day, it skins and gels once opened.
Not for
Use as a membrane or moisture barrier (use ACTFLEX EP250 or MB200), leaving it exposed (not UV stable, overcoat with 906 WPU), solvent-based ACTFLEX 929 SL or 929 HV (use ACTFLEX 700 PU PRIMER), damp substrates, or application outside 10 to 26°C. Non-porous substrates only after checking with Forspec. Vapours are combustible: no ignition sources, and keep it out of pits and basements.
All times at 25°C and 50% RH.
Accessories you might need
Technical overview
- ACTFLEX 600 PRIMER is a one-component, moisture-cured hybrid polyurethane primer engineered as the bonding primer for ACTFLEX 906 WPU.
- The hybrid chemistry interacts with the substrate to build a molecular interlocking interface, penetrating deeply into new and aged concrete, consolidating rendered and masonry surfaces and establishing a durable bonding plane on compressed fibrous cement, precast panels and existing waterproofing layers.
- It cures on atmospheric moisture yet accepts the water-based ACTFLEX 906 WPU membrane directly over the cured film.
- AS/NZS 4858 does not apply to the primer itself; system compliance is established by the certified ACTFLEX 906 WPU membrane applied over it.
- No accredited certificate is currently held and all performance values are published as typical R&D characteristic values.
Key applications
- Bonding primer beneath ACTFLEX 906 WPU water-based polyurethane waterproofing membrane
- New and aged concrete substrates
- Rendered surfaces and masonry structures
- Compressed fibrous cement sheeting
- Precast concrete panels and smooth factory-finished surfaces
- Existing waterproofing layers, for intercoat bonding in repair and maintenance
- Porous and non-porous substrates, subject to confirmation with a FORSPEC representative
Surface suitability
- New and aged concrete (clean, dry, stable and free of laitance and weak layers)
- Rendered surfaces and masonry structures
- Compressed fibrous cement sheeting
- Precast concrete panels and smooth factory-finished surfaces
- Existing waterproofing layers, for intercoat bonding in repair and maintenance
- Non-porous substrates (decontaminated by wiping with solvent or degreaser, and only after confirmation with a FORSPEC representative)
Not a waterproofing membrane and not a moisture barrier - where moisture control is required, specify ACTFLEX EP250 or ACTFLEX MB200. Not UV stable; the primed surface must be overcoated with ACTFLEX 906 WPU and never left exposed. Formulated for the ACTFLEX 906 WPU system - for solvent-based ACTFLEX 929 SL and ACTFLEX 929 HV systems specify ACTFLEX 700 PU PRIMER. Apply ONE coat only. Do not apply below 10C or above 26C substrate and ambient temperature. Do not dilute unless approved in writing by an authorised FORSPEC representative. Use all contents within the same day of opening - the product is moisture-cured and will skin and gel in a part-used container. Confirm suitability with a FORSPEC representative before use on non-porous substrates. Do not apply over damp substrates or where high moisture content is present. The uncured product and its vapours are combustible - exclude all ignition sources, and do not store or use in pits, depressions, basements or areas where vapours may be trapped.
Shipping and returns
Why waterproofers use ACTFLEX 600 PRIMER Hybrid
Moisture cured, yet directly overcoatable with water-based membranes
Waterproof within 3 hours and fully cured within 6 hours at 25C, 50% RH
How to apply ACTFLEX 600 PRIMER Hybrid
Step by step from the technical data sheet. Always read the full TDS before you start.
-
1
Clean the surface, removing dust, dirt, oil, grease, wax and all loose contaminants
-
2
Where necessary, mechanically grind or abrade to remove old coatings, laitance and weak layers
-
3
Reinstate cracks, holes and surface irregularities with FORBUILD 100 or FORCRETE 100, finished flush and cured
-
4
Confirm the substrate is stable, sound and free from movement or flaking
-
5
Decontaminate non-porous surfaces by wiping with solvent or degreaser to remove surface residue
-
6
Confirm the substrate is dry and that moisture content will not compromise adhesion
-
7
Vacuum or blow clean to remove fine dust immediately before priming
-
8
Conduct a small adhesion test on critical surfaces to confirm compatibility where required
-
9
Stir the product thoroughly and gently before use, without whipping air into it
-
10
Ensure continuous ventilation and exclude all ignition sources throughout application
-
11
Apply ONE even coat by roller, brush or approved spray at 4-6 m2 per litre to achieve 50-100 microns dry film
-
12
Work to full coverage across all edges, junctions and transitions, avoiding puddling and over-application
-
13
Reseal the container tightly whenever not in use and use all contents within the same day
-
14
Inspect for missed areas, pinholes and glossy puddled zones before the membrane is applied
-
15
Confirm the primer is touch dry, approximately 20 minutes at 25C and 50% RH, then apply ACTFLEX 906 WPU within the same working session
Specifications
Every figure from the technical data sheet, in one table.
Customer reviews
Common questions
-
Where is ACTFLEX 600 Primer used?
600 Primer is a hybrid solvent-based moisture-cured primer for both porous AND non-porous substrates - concrete, render, precast, fibre cement, and existing waterproofing systems. The hybrid chemistry handles the substrates most other primers can't span.
-
Coverage and cure?
Coverage is 4-6 m² per litre. Touch-dry in 15-30 minutes, full cure in 6 hours at 25°C/50% RH. Apply 50-100 microns DFT. Ready-to-use - no mixing or dilution required.
-
Which membranes is it compatible with?
Compatible with both water-based AND solvent-based ACTFLEX membranes - one primer for the whole range. This is the workhorse Forspec primer for typical project work.
-
Application temperature range?
Apply between 10-26°C ambient. Same-day reactivation is possible if the can has been opened recently. Once cured (6 hours), prime is ready for membrane application.
-
Is 600 Primer a vapour barrier?
No - 600 Primer is NOT a moisture vapour barrier. For projects with significant moisture vapour issues (high RH concrete, suspect slabs), use ACTFLEX MB200 or EP 250 to block vapour transmission.
Ready to order?
Dispatched same or next business day from Roselands NSW. Questions? Call the team on (02) 8021 3517.

