ACTFLEX 400 CLEAR Temporary Leak Repair Kit For Leaking Bathrooms & Balconies
Fix a leaking bathroom or balcony without lifting a tile. The over-tile repair kit, sized to the job.
Built around ACTFLEX 400 CLEAR, a temporary clear leak repair coating that goes straight over existing tiles. Not a waterproofing membrane. Fill the corners, roll on three thin coats, and the leak is fixed for up to five years. 1 kg, 3 kg or 7 kg kits.
What's in the kit
- ACTFLEX 400 CLEAR coating, 1 kg, 3 kg or 7 kg pack
Where to use it
- Leaking tiled showers and internal wet areas
- Leaking tiled balconies, courtyards and terraces
- Parapet walls, hobs and building exteriors
Why buy the kit
- No primer, no system build-up. Three thin coats on a clean, sound, dry surface
- Clear semi-gloss finish keeps the original look of the tiles
- UV resistant. Foot traffic once cured
- A fraction of the cost of ripping up and re-waterproofing
- Brush or roller diluted 2:1 with water, first coat with a mohair roller. Corners filled first with ACTFLEX MS PRO or Soudal T-Rex
- Fix loose tiles and grout first. Not a crack repair. No product warranty
Coverage
Diluted 2:1 over tiles, three coats: 1 kg approx. 3 m², 3 kg approx. 9 m², 7 kg approx. 21 m². Keep rain off for 3 to 5 days after the final coat.
Accessories you might need
Technical overview
- ACTFLEX 400 CLEAR is a single-pack co-polymer emulsion with synthetic rubber latex, supplied here as a kit for stopping leaks through tiled bathrooms, showers, balconies and terraces without removing the tiles.
- It is applied over the existing tiles as three thin coats with no primer and no system build-up, with all corners, junctions and penetrations filled and filleted first, and it fixes the leak for up to five years.
- It is not a waterproofing membrane and is never specified as one, and no membrane classification applies or is claimed.
- No accredited test reports exist for this product and all performance values are published as typical Forspec R&D characteristic values.
- No product or performance warranty is offered.
Key applications
- Leaking tiled balconies, courtyards and terraces - remedial waterproofing over the existing tiles
- Leaking tiled showers and internal wet areas
- Parapet walls, hobs and building exteriors - stopping water ingress through the external envelope
- Waterproofing of terracotta tiles and pavers
- Top-coating and sealing of timber floors
- Sealing sandstone surfaces and face brick walls
Surface suitability
- Tiles (every broken, popping or loose tile replaced first; moisture below 4%)
- Grout lines and mortar joints (all compromised, loose or damaged grout replaced first)
- Concrete and level surfaces (0.5 mm minimum dry film thickness)
- Terracotta tiles and pavers
- Timber floors (top-coating and sealing)
- Sandstone surfaces
- Face brick walls
- Parapet walls and hobs (stopping water ingress through the external envelope)
A temporary solution only - it fixes the leak for up to 5 years, it is not a waterproofing membrane and is never specified as one, and no product or performance warranty is offered. It does not fix broken, popping or loose tiles or loose grout; every defective tile and grout line is rectified first and all cracks repaired with ACTFLEX MS PRO or Soudal T-Rex before application. Never apply to a damp surface - substrate moisture must be below 4% and the surface completely dry, and never apply over water trapped beneath the tiles until the substrate has been aerated 3-5 days and confirmed dry. Do not apply below 10C surface temperature. Apply all coats within 48 hours of each other. No rain, washing or standing water on the surface for at least 3-5 days after the final coat. The film may turn cloudy white where water ponds or sits and some yellowing may occur within the service life. Not slip-resistant as supplied - broadcast ACTFLEX ANTISLIP to the designed slip rating. Complete an adhesion trial area on every substrate before full application. Classified a Hazardous Chemical and Dangerous Goods - causes skin and serious eye irritation, may cause respiratory irritation, and is toxic to aquatic life with long lasting effects.
Shipping and returns
Why waterproofers use ACTFLEX 400 CLEAR Temporary Leak Repair Kit For Leaking Bathrooms & Balconies
Three thin coats, no primer and no system build-up
Clear semi-gloss finish, UV resistant and foot-trafficable once cured
How to apply ACTFLEX 400 CLEAR Temporary Leak Repair Kit For Leaking Bathrooms & Balconies
Step by step from the technical data sheet. Always read the full TDS before you start.
-
1
Inspect every surface: it must be stable, sound and structurally intact, free of voids, protrusions and movement
-
2
Replace broken, popping or loose tiles and remove all compromised, loose or damaged grout, replacing it with new grout, ACTFLEX MS PRO or Soudal T-Rex
-
3
Repair all cracks in concrete, render or screeds with ACTFLEX MS PRO or Soudal T-Rex before coating
-
4
Remove dust, grease, laitance and all loose, flaking or friable material with stiff brushes, scrapers and vacuum equipment
-
5
Treat moss and mould with household bleach diluted 1 part bleach to 2 parts water, rinse thoroughly with clean water and allow to dry completely
-
6
Remove grease with appropriate detergents, rinse the detergent off, final-rinse with clean water and dry
-
7
Where water is trapped beneath the tiles, aerate the substrate for a minimum of 3-5 days and confirm it is dry
-
8
Confirm the surface has stayed moisture-free for at least 3-5 days with moisture content below 4%
-
9
Fill and fillet all corners, wall and floor junctions, hob junctions and penetrations with ACTFLEX MS PRO or Soudal T-Rex, tooled smooth and cured tack free
-
10
Complete an adhesion trial area on the substrate before full application
-
11
Stir thoroughly before use to a uniform consistency
-
12
Use neat and undiluted for trowel application; for brush or roller dilute 2 parts ACTFLEX 400 CLEAR to 1 part clean water, mechanically stirred
-
13
Apply the first coat with a mohair roller for full wetting into grout lines and surface texture
-
14
Allow a minimum of 4 hours between coats at 25C and 50% RH and apply all coats within 48 hours
-
15
Build three thin, even coats to 0.2 mm dry film thickness over tiles and 0.5 mm over joins, grout lines, mortar, concrete and level surfaces
-
16
Where slip resistance is required, broadcast ACTFLEX ANTISLIP onto the wet second coat and lock it in with the third coat
-
17
Check for a continuous, pinhole-free film over every grout line and junction, fillets fully encapsulated and no ponded material
-
18
Keep rain, washing and standing water off the surface for at least 3-5 days; full cure is 5-7 days after the final coat
Specifications
Every figure from the technical data sheet, in one table.
Customer reviews
Common questions
-
What's in the ACTFLEX 400 Clear Bathroom and Balcony Repair Kit?
The kit contains the full ACTFLEX 400 Clear over-tile waterproofing system: clear-finish membrane, application tools (brush, roller), reinforcement tape for problem areas, and step-by-step instructions for over-tile remedial waterproofing.
-
Why apply over existing tiles?
Demolishing and retiling a leaking bathroom or balcony is expensive and disruptive. ACTFLEX 400 Clear bonds to clean existing tiles and forms a clear leak repair coating that preserves the original look while stopping leaks for up to 5 years. It is a temporary fix, not a waterproofing membrane.
-
What prep is required?
Critical: clean the existing tiles thoroughly with detergent and a degreaser, remove all mould (treat with bleach if needed), regrout failing joints with epoxy grout, and let everything dry. Then apply 400 Clear per the supplied instructions.
-
Will it work on natural stone or coloured tiles?
ACTFLEX 400 Clear is genuinely clear once cured, preserving the appearance of underlying tiles. On porous natural stones, test a small area first - some stones may darken slightly under the clear coating.
-
Is the repaired surface AS-compliant?
ACTFLEX 400 Clear is a remedial system - it extends the service life of a previously waterproofed (and now leaking) surface. For new-build wet area waterproofing, AS3740:2021 specifies an under-tile membrane like ACTFLEX 906 WPU.
Ready to order?
Dispatched same or next business day from Roselands NSW. Questions? Call the team on (02) 8021 3517.

