FORSPEC ACTFLEX Ultra Shield Part A and Part B high-performance two-component polyaspartic coating kit
ACTFLEX ULTRA SHIELD
ACTFLEX ULTRA SHIELD

ACTFLEX ULTRA SHIELD

Sale price$660.00

Direct to concrete polyaspartic floor coating. 90% solids, hard through in 3.5 hours, full cure in 48.

ACTFLEX ULTRA SHIELD is a two-component elastomeric polyaspartic floor coating at 90% solids. It goes straight onto prepared concrete, so a garage or warehouse floor can be coated and handed back inside a single shift. Roll it as a solid colour or broadcast flake into it.

Where to use it

  • Garage floors and commercial, industrial and residential flooring
  • Flooring within food processing plants
  • High-wear and traffic-prone areas, and permanent immersion

Why waterproofers buy it

  • Applied direct to well-prepared concrete, no separate membrane required
  • Recoat in 1 to 4 hours, hard through in 3.5 hours, full cure in 48 hours
  • High UV stability with outstanding resistance to yellowing
  • Elastomeric film bridges hairline cracks and absorbs minor substrate movement
  • High abrasion-resistant vehicular traffic durability
  • No joints or laps. Roller, brush or spray, 30 minute pot life
  • Clear or custom UV-stable colours. 20 L and 40 L packs
  • 10 year Forspec product warranty

Coverage

6 to 8 m²/L per coat.
20 L pack: approximately 120 to 160 m² per coat.
40 L pack: approximately 240 to 320 m² per coat.
Flake systems use much more clear coat.

Not for

Slip-rated floors without an anti-slip broadcast (not slip-resistant as supplied), below 10°C or above 30°C, substrates over the moisture limit without two coats of ACTFLEX EP250, designed movement joints, structural repair or levelling. Remove old paint and resin coatings first. Mix full kits only.

All times at 25°C and 50% RH.

Applied direct to well-prepared concrete - no separate membrane required
Hard through in 3.5 hours, fully cured in 48 hours at 25C, 50% RH
Elastomeric film bridges hairline cracks and absorbs minor substrate movement
Choose your size
1
7-Day ReturnsMoney back
Fast DispatchNext business day
Expert Advice(02) 8021 3517
Secure CheckoutSSL encrypted
Accessories you might need
ACTFLEX 700 PU Primer ACTFLEX 700 PU PrimerPrimer $88.00
ACTFLEX 101 UV Stable Trafficable Membrane ACTFLEX 101 UV Stable Trafficable MembraneTape and reinforcement $250.00
2L Nylex Hand Sprayer 2L Nylex Hand SprayerTop coat $15.00
Technical overview
  • ACTFLEX Ultra Shield is a two-component elastomeric polyaspartic floor coating at 90% solids, applied direct to well-prepared concrete to deliver a seamless, high-strength decorative and protective floor.
  • Polyaspartic chemistry combines an extended pot life with a fast return to service and outstanding resistance to yellowing.
  • The elastomeric formulation bridges hairline cracks and absorbs minor substrate movement, and the coating can be applied as a solid colour or built into a decorative flake system.
  • It is not rated for slip resistance as supplied - an anti-slip broadcast is required to achieve a designed rating.
  • No accredited certificate is currently held on file for ACTFLEX ULTRA SHIELD and all performance values are published as typical R&D characteristic values.
Key applications
  • Direct-applied protective and decorative floor coating over prepared concrete
  • Garage floors and commercial, industrial and residential flooring
  • Flooring within food processing plants
  • High-wear and traffic-prone environments
  • Permanent immersion situations
  • Decorative flake or solid-colour floor finishes
  • Areas requiring enhanced surface friction, with the specified anti-slip broadcast
Surface suitability
  • Concrete (structurally sound, mechanically prepared by diamond grinding or shot blasting to an open, sound profile)
  • Concrete with substrate moisture within the stated limit (apply ACTFLEX EP250 as a two-coat moisture-control system where the limit is exceeded)
  • Floors with all previous paint and resin coatings completely removed
  • Floors with cracks and spalling reinstated with FORBUILD 100, FORCRETE 100 or the FORSPEC epoxy crack repair range

Two-component product - mix full kits only and observe the 30-minute pot life; do not part-mix and never re-temper. Not slip-resistant as supplied - an anti-slip broadcast is required to achieve a designed slip rating. Do not apply below 10C or above 30C. Do not apply over substrates exceeding the stated moisture limit - apply ACTFLEX EP250 as a two-coat moisture-control system where the limit is exceeded. Do not dilute unless approved in writing by an authorised FORSPEC representative. Not a structural repair product - cracks and spalling must be reinstated before coating. Bridges hairline cracks only; it does not accommodate designed movement joints, which must be carried through the coating. All previous paint and resin coatings must be completely removed before application. Not a levelling product - the finished surface follows the prepared substrate profile. Both components are classified hazardous: Part A may cause genetic defects and may cause cancer, and Part B is a flammable liquid and vapour that is harmful if inhaled and may cause allergy or asthma symptoms or breathing difficulties if inhaled. Read both Safety Data Sheets before use.

Shipping and returns
Dispatched same or next business day from Roselands NSW, with fast delivery Australia wide. 7-day returns on unused stock in original packaging (20% restocking fee).
Technical documents
ACTFLEX ULTRA SHIELD
ACTFLEX ULTRASHIELD - Clear / 8 Litre
$660.00
1

Why waterproofers use ACTFLEX ULTRASHIELD

Applied direct to well-prepared concrete - no separate membrane required
01

Applied direct to well-prepared concrete - no separate membrane required

Hard through in 3.5 hours, fully cured in 48 hours at 25C, 50% RH
02

Hard through in 3.5 hours, fully cured in 48 hours at 25C, 50% RH

03

Elastomeric film bridges hairline cracks and absorbs minor substrate movement

How to apply ACTFLEX ULTRASHIELD

Step by step from the technical data sheet. Always read the full TDS before you start.

  1. 1

    Inspect the floor thoroughly and confirm it is structurally sound, clean and free of damage, checking for cracks, holes and surface imperfections

  2. 2

    Remove all contaminants - dust, grease, oil, wax, paint and other residues - using a degreaser where required, followed by a rinse with clean water, and allow to dry fully

  3. 3

    Where the surface carries a previous paint or resin coating, remove it completely by sanding, grinding or abrasive blasting

  4. 4

    Repair all cracks and spalling with a FORSPEC concrete repair system such as FORBUILD 100 or FORCRETE 100, or the FORSPEC epoxy crack repair range, finished flush and cured

  5. 5

    Mechanically prepare the substrate by diamond grinding or shot blasting to an open, sound profile and vacuum thoroughly

  6. 6

    Confirm substrate moisture is within the limit stated in the Technical Data; where the limit is exceeded, apply ACTFLEX EP250 as a two-coat moisture-control system

  7. 7

    Vacuum the area immediately before application

  8. 8

    Pre-condition both components before mixing and mix full kits only - never part-mix

  9. 9

    Combine the components and mix with a low-speed mechanical mixer to a uniform, streak-free blend, scraping the sides and base of the container, without whipping air into the mix

  10. 10

    Mix only the quantity that can be placed within the 30-minute pot life

  11. 11

    Apply by roller, brush or spray at 6-8 m2 per litre, working to a uniform, continuous film

  12. 12

    Maintain a wet edge and consistent overlap - polyaspartic films are unforgiving of dry laps

  13. 13

    For a decorative flake finish, broadcast the flake into the wet base coat to the required density, allow to cure, remove all loose flake by vacuum and scrape, then apply the clear lock coat

  14. 14

    Where enhanced surface friction is specified, broadcast the anti-slip aggregate into the wet coat and lock it in with a further coat

  15. 15

    Apply subsequent coats within the 1-4 hour recoat window at 25C and 50% RH

  16. 16

    Protect the finished floor from water, contamination and traffic until hard through

  17. 17

    Inspect the finished film for holidays, pinholes, flake shadowing and inconsistent gloss before releasing the area

Specifications

Every figure from the technical data sheet, in one table.

Property
Value
Membrane Classification
Two-component elastomeric polyaspartic floor coating
Solids Content
90%*
Chemical Base
Polyaspartic, two component
Colour
Clear or custom colours
Shore Hardness A
93*
Shore Hardness D
56*
Elongation at Break
Less than 100%*
Moisture Vapour Transmission
Pass (ASTM E96, manufacturer data)*
Fatigue Cracking
Pass, no fatigue cracking*
Physical or Chemical Damage
None recorded*
Flash Point
97C*
Pot Life
30 minutes at 25C, 50% RH
Recoat Window
1-4 hours at 25C, 50% RH
Hard Through
3.5 hours at 25C, 50% RH
Full Cure
48 hours at 25C, 50% RH
Light Foot Traffic
After hard through*
Vehicle Traffic
After full cure*
Permanent Water Immersion
After full cure*
Application Temperature
+10C to +30C
Maximum Substrate Moisture
5%*
Coverage
6-8 m2/L per coat*
Consumption Per Coat
Approx. 0.13-0.17 L/m2*
Slip Resistance
Not rated as supplied - an anti-slip broadcast is required to achieve a designed rating
Packaging
4 L, 20 L and 40 L
Shelf Life
12 months, unopened, stored as specified*
Hazard Classification
Hazardous substance (GHS); Part B dangerous goods, Poison Schedule Number 6
* Typical Forspec R&D characteristic values - no accredited test report is held for this product
Download the full technical data sheet

Customer reviews

Ready to order?

1

Dispatched same or next business day from Roselands NSW. Questions? Call the team on (02) 8021 3517.