ACTFLEX ATC Top Coat 15L

ACTFLEX ATC Top Coat 15L

Sale price$660.00

UV-stable trafficable topcoat for exposed Forspec PU and polyurea membranes. 2,000 hours UVB with no cracking, blistering or chalking.

ACTFLEX ATC is a single-pack, moisture-curing aliphatic polyurethane topcoat. Roll it over a cured FORSPEC polyurethane or polyurea membrane and the system becomes trafficable, taking foot and vehicle traffic and standing up to oils, cleaning agents and harsh chemicals. Clear or grey. 15 L pack.

Where to use it

  • Over cured FORSPEC polyurethane and polyurea membranes only
  • Exposed balconies, terraces and podium decks
  • Rooftops and other exposed horizontal surfaces
  • Car parking decks and vehicle-trafficked membrane areas

Why waterproofers buy it

  • UV stable: 2,000 hours accelerated UVB to ASTM G154-16, accredited test data, no visible cracking, blistering or chalking
  • Aliphatic, so it holds its gloss instead of slowly yellowing
  • High chemical resistance to oils, cleaning agents and harsh chemicals
  • Single pack, moisture curing. No mix ratio, no pot life, no mixed waste
  • Tack free 3 hours, second coat at 4 to 6 hours, cured at 12 hours
  • 10 year Forspec product warranty

Coverage

6 to 8 m² per litre per coat, two coats. 15 L pack: about 90 to 120 m² one coat, 45 to 60 m² two coats.

Not for

Waterproofing on its own (it protects a membrane), anything but cured FORSPEC PU or polyurea without Forspec sign-off, substrate moisture over 5%, below 5°C or above 35°C, immersion, or filling defects. Combustible while uncured, keep ignition sources away.

All times at 25°C and 50% RH.

2,000 hours accelerated UVB to ASTM G154-16 with no cracking, blistering or chalking
Single-pack moisture-curing, so no mixing ratio and no pot life
Trafficable finish rated for both foot and vehicle traffic
1
7-Day ReturnsMoney back
Fast DispatchNext business day
Expert Advice(02) 8021 3517
Secure CheckoutSSL encrypted
Accessories you might need
Technical overview
  • ACTFLEX ATC is a single-pack, moisture-curing aliphatic polyurethane topcoat for the exposed face of a FORSPEC waterproofing system.
  • It is applied only over cured FORSPEC polyurethane and polyurea membranes, converting a protected system into a trafficable one that takes both foot and vehicle traffic while resisting oils, cleaning agents and harsh chemicals.
  • It is not a waterproofing membrane.
  • ACTFLEX ATC carries accredited UV exposure data to ASTM G154-16, 2,000 hours of accelerated UVB with no visible cracking, blistering or chalking.
  • All other performance values are published as typical Forspec R&D characteristic values, and no VOC certificate is currently held.
Key applications
  • Protective UV topcoat over cured FORSPEC polyurethane and polyurea waterproofing membranes
  • Exposed balconies, terraces and podium decks
  • Rooftops and exposed horizontal surfaces
  • Car parking decks and vehicle-trafficked membrane areas
  • Plant rooms, service areas and exposed plinths
  • Any location where a waterproofing membrane remains permanently exposed to sunlight
  • Refreshing and re-protecting existing FORSPEC polyurethane topcoat systems
Surface suitability
  • Cured FORSPEC polyurethane waterproofing membranes
  • Cured FORSPEC polyurea waterproofing membranes
  • Any other system only where compatibility is confirmed by a FORSPEC representative
  • Existing FORSPEC polyurethane topcoat systems being refreshed and re-protected

Not a waterproofing membrane. ACTFLEX ATC protects a membrane, it does not waterproof an area. Apply only over cured FORSPEC polyurethane and polyurea membranes; confirm compatibility with a FORSPEC representative before use over any other system. Do not apply where substrate moisture exceeds 5%, below 5C or above 35C substrate temperature. Do not dilute unless expressly instructed in writing by an authorised FORSPEC representative. Where the membrane has been cured and left exposed for more than 24 hours before topcoating, thorough cleaning is mandatory. Beyond the 36 hour maintenance recoat window the surface must be abraded and cleaned before recoating. Not a levelling or filling product - rectify surface defects, pinholes and membrane irregularities first. Not for immersion service without written FORSPEC approval. The uncured product and its vapours are combustible, so exclude all ignition sources.

Shipping and returns
Dispatched same or next business day from Roselands NSW, with fast delivery Australia wide. 7-day returns on unused stock in original packaging (20% restocking fee).
Technical documents
ACTFLEX ATC Top Coat 15L
ACTFLEX ATC
$660.00
1

Why waterproofers use ACTFLEX ATC

01

2,000 hours accelerated UVB to ASTM G154-16 with no cracking, blistering or chalking

02

Single-pack moisture-curing, so no mixing ratio and no pot life

03

Trafficable finish rated for both foot and vehicle traffic

How to apply ACTFLEX ATC

Step by step from the technical data sheet. Always read the full TDS before you start.

  1. 1

    Confirm the FORSPEC waterproofing membrane is fully cured in accordance with its Technical Data Sheet

  2. 2

    Inspect the membrane for contaminants, dust, pinholes, damage and surface irregularities and rectify every defect

  3. 3

    Clean thoroughly by the FORSPEC approved method where the membrane has been left exposed for more than 24 hours

  4. 4

    Confirm substrate moisture does not exceed 5%

  5. 5

    Remove all dust and debris by vacuum or compressed air immediately before coating

  6. 6

    Confirm substrate and ambient temperature are between 5C and 35C and that no rain is forecast before the film is tack free

  7. 7

    Stir the product thoroughly and gently before use, without whipping air into it

  8. 8

    Apply the first coat by roller, brush or airless spray at a coverage rate of 6-8 m2 per litre

  9. 9

    Work to a uniform, continuous film with consistent overlap and no holidays, ribbing or pooling

  10. 10

    Allow the first coat to dry for 4-6 hours, depending on temperature and humidity

  11. 11

    Apply the second coat at the same coverage rate, ensuring proper overlap between coats

  12. 12

    Protect the finished coating from rain, standing water and traffic until cured

  13. 13

    Inspect the finished film for holidays, pinholes and inconsistent gloss before releasing the area

  14. 14

    Release to foot and vehicle traffic only after full cure

Specifications

Every figure from the technical data sheet, in one table.

Property
Value
Product Type
Single-pack, moisture-curing aliphatic polyurethane topcoat
Colour
Clear or grey
Hardness
90 +/- 5 Shore A (AS 1683.15)*
Tensile Strength
> 30 MPa (ASTM D412)*
Elongation at Break
> 140% (ASTM D412)*
Non-Volatile Content
68 +/- 2% (ASTM D3960)*
Density - Liquid
1.04 g/cm3*
Density - Cured Solid
1.12 g/cm3*
UV Resistance
2,000 hours accelerated UVB, no visible cracks, blistering or chalking (ASTM G154-16)
Coverage
6-8 m2/L per coat
Coats
2 where full film build and durability are required
Tack Free Time
3 hours @ 25C, 50% RH*
Intercoat Drying Before Second Coat
4-6 hours @ 25C, 50% RH
Cure Time
12 hours @ 25C, 50% RH*
Foot Traffic
After full cure*
Vehicle Traffic
After full cure*
Maintenance Recoat Window
After 12 hours and before 36 hours @ 25C, 50% RH
Recommended Substrate Temperature
+5C to +35C
Maximum Substrate Moisture
5%
Service Temperature
-20C to +80C
Shelf Life
12 months unopened, stored as specified*
* Typical Forspec R&D characteristic values
Download the full technical data sheet

Customer reviews

Common questions

View all FAQs
  • What is ACTFLEX ATC Top Coat used for?

    ATC Top Coat is a single-pack aliphatic polyurethane top coat applied over PU/polyurea waterproof membranes to provide UV protection, chemical resistance, and a trafficable finish. Suitable for both foot and vehicle traffic.

  • What's the coverage?

    Coverage is 0.4 kg/m² for light pedestrian traffic (one coat) or 0.8 kg/m² for vehicle traffic (two coats), achieving approximately 0.2mm DFT. Touch-dry in 3 hours, recoat in 12 hours, waterproof in 5 hours.

  • How is it applied?

    ATC is single-pack moisture-curing - no mixing required. Apply by roller or brush over the cured membrane. Self-levelling formula gives a smooth finish. Service temperature range -20°C to +80°C once cured.

  • What's the UV/weathering performance?

    ATC is low-VOC certified and tested to 2000 hours UVB accelerated weathering. Bond strength to substrate exceeds 1.5 MPa with over 140% elongation. Grey is the standard colour; custom colours available.

  • Which membranes can ATC be applied over?

    Compatible with the full ACTFLEX polyurethane membrane range including 929 HV/SL, 925 SFPU, and 906 WPU. Use ATC for cost-effective UV protection where ULTRA FC's polyaspartic premium isn't required.

Ready to order?

1

Dispatched same or next business day from Roselands NSW. Questions? Call the team on (02) 8021 3517.