Forspec ACTFLEX 700 PU Primer polyurethane primer for waterproofing membrane systems

ACTFLEX 700 PU Primer

Sale price$88.00

The speed primer under ACTFLEX 929 SL and 929 HV. Touch dry in 30 minutes, membrane on within hours.

ACTFLEX 700 PU PRIMER is a single-pack, moisture-curing polyurethane primer for porous substrates under Forspec solvent-based membranes. It is the specified primer for ACTFLEX 929 SL and 929 HV, and the bonding agent for recoating old solvent-based PU membranes. One coat, no mixing, straight from the can. 4 L and 17 L.

Where to use it

  • Porous substrates under Forspec solvent-based membranes, including the ACTFLEX moisture-cured PU range
  • Under ACTFLEX 75FC and Forspec solvent-based joint sealants on dry internal surfaces
  • Recoating and tying into existing solvent-based PU liquid membranes
  • New and old concrete, renders, masonry, brickwork and timber
  • Wet-area-grade fibre cement and compressed fibre cement sheet

Why waterproofers buy it

  • Touch dry in as little as 30 minutes, waterproof in 3 hours, full cure in 6 hours
  • One even coat. No multi-coat priming on porous substrates
  • Penetrating film consolidates porous surfaces
  • Translucent matte finish, so you can still see the substrate
  • Brush, roller or approved spray
  • 10 year Forspec product warranty

Coverage

One coat at 4 to 6 m² per litre, 60 micron nominal DFT. 4 L: approx. 16 to 24 m². 17 L: approx. 68 to 102 m². Overcoat once touch dry and within 24 hours, or re-prime.

Not for

Moisture control (it blisters and peels on a damp substrate, use ACTFLEX EP250 or MB200), water-based products, leaving exposed beyond 48 hours after full cure, or application outside 10 to 26°C. Do a staining trial on every substrate. Use an opened can the same day. Flammable liquid and vapour: no ignition sources, ventilate, and never store in pits or basements.

Touch dry at 20°C and 50% RH. Other times at 25°C and 50% RH.

Touch dry in as little as 30 minutes - the speed primer of the range
Single pack, one coat, no mixing ratios straight from the can
The specified primer for ACTFLEX 929 SL and 929 HV systems
Choose your size
1
7-Day ReturnsMoney back
Fast DispatchNext business day
Expert Advice(02) 8021 3517
Secure CheckoutSSL encrypted
Accessories you might need
Technical overview
  • ACTFLEX 700 PU Primer is a single-pack, fast-drying, moisture-curing polyurethane primer formulated to enhance adhesion between porous substrates and Forspec solvent-based waterproofing membranes and joint sealants, specifically ACTFLEX 929 SL and ACTFLEX 929 HV.
  • It also functions as a bonding agent for re-coating existing solvent-based polyurethane liquid membranes.
  • Applied as one even coat at a nominal 60 micron dry film thickness.
  • Touch dry in 30 minutes at 20C; full cure in 6 hours at 25C, 50% RH.
  • It is a primer, not a moisture barrier - specify ACTFLEX EP250 or ACTFLEX MB200 where substrate moisture control is required.
  • No Australian Standard prescribes performance requirements for solvent-based polyurethane primers of this type; system compliance is carried by the host membrane or sealant applied over it.
  • No accredited test reports exist for this product and all performance values are published as typical Forspec R&D characteristic values.
Key applications
  • Priming porous substrates beneath Forspec solvent-based waterproofing membranes
  • Priming beneath ACTFLEX 75FC and Forspec solvent-based joint sealants on dry internal surfaces
  • Bonding agent for re-coating and tying into existing solvent-based polyurethane liquid membranes
  • Consolidating primer for new and old concrete, renders, masonry, brickwork and timber
  • Priming wet-area-grade fibre cement and compressed fibre cement sheeting
Surface suitability
  • New and old concrete
  • Render
  • Masonry
  • Brickwork
  • Timber
  • Wet-area-grade fibre cement and compressed fibre cement sheeting (per the host system TDS)
  • Existing solvent-based polyurethane liquid membranes (sound, well-bonded, clean and dry, glossy surfaces abraded)

NOT a moisture or vapour barrier - substrate moisture causes the primer to blister and peel; specify ACTFLEX EP250 or ACTFLEX MB200 where moisture control is required. Never use under or with water-based products. Not UV stable - never leave the primed surface exposed beyond 48 hours after full cure. Staining may occur on some substrates - complete a sample trial area on every substrate first. Opened containers must be used the same day. Apply only between 10-26C ambient and substrate, never below 10C surface temperature. Flammable liquid and vapour - exclude all ignition sources during application and cure, ventilation mandatory, and never store in pits, depressions, basements or anywhere vapours can trap.

Shipping and returns
Dispatched same or next business day from Roselands NSW, with fast delivery Australia wide. 7-day returns on unused stock in original packaging (20% restocking fee).
Technical documents
ACTFLEX 700 PU Primer
ACTFLEX 700 PU - 4 LT
$88.00
1

Why waterproofers use ACTFLEX 700 PU

01

Touch dry in as little as 30 minutes - the speed primer of the range

02

Single pack, one coat, no mixing ratios straight from the can

03

The specified primer for ACTFLEX 929 SL and 929 HV systems

How to apply ACTFLEX 700 PU

Step by step from the technical data sheet. Always read the full TDS before you start.

  1. 1

    Confirm the substrate is structurally sound, dry, clean and free of dust, laitance, oils, grease, curing compounds, coatings and all loose or friable material

  2. 2

    Repair holes and non-moving cracks with FORBUILD 100, FORCRETE 100 or the Forspec epoxy crack repair range, cured and prepared per its TDS

  3. 3

    For re-coating existing polyurethane membranes, confirm the membrane is sound, well-bonded, clean and dry; abrade glossy surfaces and remove all contamination

  4. 4

    Complete the staining trial area and confirm the result before full application

  5. 5

    Stir the product thoroughly and gently before use - do not whip air in

  6. 6

    Ensure continuous ventilation and exclude all ignition sources

  7. 7

    Apply ONE even coat by brush, roller or approved spray at 4-6 m2/L, working the primer into the surface texture without ponding or heavy film build

  8. 8

    Allow the primer to become touch dry - as little as 30 minutes at 20C, 50% RH

  9. 9

    Check full even coverage with no misses or ponds, and confirm touch dry by firm finger touch with no transfer

  10. 10

    Install backing rod, sealant or the waterproofing membrane system and complete over-coating within a maximum of 24 hours; re-prime where the window is exceeded

Specifications

Every figure from the technical data sheet, in one table.

Property
Value
Membrane Classification
Polyurethane Primer (solvent-based)
Solids Content
Greater than 30% (volatile content less than 70% w/w)*
Chemical Base
Single-pack moisture-curing polyurethane resin
Cure Mechanism
Reacts with atmospheric moisture
Colour
Translucent matte, viscous liquid; solvent odour
Density
0.80-1.00 g/mL @ 25C*
Vapour Pressure
3.8 kPa @ 25C*
Flash Point
Greater than 23C - flammable liquid and vapour
Touch Dry
30 minutes @ 20C, 50% RH; 15 minutes @ 30C, 50% RH*
Waterproof Time
3 hours @ 25C, 50% RH*
Full Cure
6 hours @ 25C, 50% RH*
Overcoat Window
Once touch dry, maximum 24 hours - re-prime if exceeded
Nominal Dry Film Thickness
60 microns, one coat
Coverage
4-6 m2 per litre per coat, porosity dependent*
Number of Coats
One coat only
Application Temperature
10-26C ambient and substrate; minimum 10C surface
Solvent Resistance (cured)
Good*
Pack Sizes
1L, 4L and 17L
Usable Period After Opening
Use within the same day - moisture cured
Shelf Life
6 months unopened, stored at 10-25C*
Hazard Classification
Hazardous Chemical; Dangerous Goods; Poisons Schedule S6
* Typical Forspec R&D characteristic values - no accredited test reports exist for this product
Download the full technical data sheet

Customer reviews

Common questions

View all FAQs
  • What is ACTFLEX 700 PU Primer for?

    700 PU Primer is a high-build moisture-curing polyurethane primer specifically for solvent-based PU membranes and joint sealants. Used over new/old concrete, render, masonry, timber, bricks, CFC sheeting, and Villaboard.

  • Why specifically for solvent-based PU?

    The 700 PU Primer chemistry is matched to solvent-based PU membranes (929 HV/SL series). It reactivates existing PU membrane surfaces, allowing fresh PU to bond to aged cured PU - critical for repair and overlay work.

  • Coverage and cure?

    Coverage is 4-6 m² per litre. Touch-dry in 30 minutes at 20°C, waterproof in 3 hours at 25°C, full cure in 6 hours. Single-component, no mixing required.

  • Is it elastomeric?

    No - 700 PU Primer is non-elastomeric. It provides bond chemistry only. The flexibility comes from the PU membrane layer applied on top. Not for continuous UV exposure - must be overcoated.

  • Shelf life and same-day use?

    Same-day use is possible after opening (moisture-reactive chemistry means once exposed, the can starts curing). Plan to use the full pail within the same project day, or seal carefully for short-term storage.

Ready to order?

1

Dispatched same or next business day from Roselands NSW. Questions? Call the team on (02) 8021 3517.