Omega PoolKote 2 Pack Epoxy Pool Paint
Two pack epoxy paint for concrete and fibreglass pools. Semi gloss, 9m² per litre per coat.
PoolKote 2 Pack Epoxy is a two pack, polyamide cured epoxy coating for concrete and fibreglass swimming pools, indoor and outdoor. It resists impact, abrasion, fungus, bacterial growth, acids, alkalis and pool chemicals, with extremely low water and water vapour permeability.
Where to use it
- Properly prepared bare concrete and fibreglass pools
- Recoating previously painted epoxy concrete and fibreglass pools
- Indoor and outdoor pools
- Designed for underwater use only, direct sunlight may cause fading, peeling or chalking
Why waterproofers buy it
- 49% volume solids, mixed 3 parts base to 1 part hardener
- Theoretical coverage 9m² per litre per coat, minimum two coats
- Semi gloss finish in 12 Poolkote colours
- Very good resistance to impact, abrasion, fungus, bacterial growth, acids, alkalis and pool chemicals
- Extremely low water and water vapour permeability
- Touch dry 2 hours, recoat 24 hours, full cure 7 days
- 4L and 20L kits
Coverage
Theoretical coverage is 9m² per litre per coat. New concrete needs a first coat thinned 20% to seal, plus one to two more coats, a minimum of two coats overall.
Not for
Once mixed, the full quantity must be applied in one session, it cannot be stored, resealed or used later. Do not apply in high humidity or below 15°C or above 30°C. New concrete must cure 28 days and be acid etched first.
Dry times at 25°C and 60% relative humidity.
7-Day Money BackGuarantee
Fast DispatchNext Business Day
Expert Advice(02) 8021 3517
Secure CheckoutSSL EncryptedPickup available at The Waterproofing Shop
Usually ready in 24 hours
Omega PoolKote 2 Pack Epoxy Pool Paint
Bright Blue / 4 Litre
The Waterproofing Shop
22/872 Canterbury Road
Roselands NSW 2196
Australia
How to Use
Technical Specifications
Frequently bought together
Technical overview
Key applications
- Bare concrete swimming pools
- Fibreglass swimming pools
- Recoating previously painted epoxy concrete pools
- Recoating previously painted epoxy fibreglass pools
- Indoor pools
- Outdoor pools
Surface suitability
- Bare concrete pools (cured at least 28 days and acid etched to create a suitable profile)
- Previously painted epoxy concrete pools (cleaned with a concentrated wash then sanded with 20-40 grit)
- Fibreglass pools (cleaned thoroughly and lightly sanded with 20-40 grit)
- Previously painted epoxy fibreglass pools
- Indoor and outdoor pools
Designed for underwater use only. Exposure to direct sunlight may cause fading, peeling or chalking. Do not apply in high humidity or when the temperature is below 15C or above 30C. New concrete must be cured for at least 28 days and acid etched. Two pack product - once mixed the full quantity must be applied in one application session and cannot be stored, resealed or used later. Allow 24 hours between coats and 7 days full cure. Chlorine and other pool chemicals cause salt build up on the paint film, so regular cleaning is required to prevent premature deterioration. Highly flammable liquid and vapour, Dangerous Goods Class 3, UN 1263, Packing Group III, and a Scheduled Poison S5. Avoid sources of heat, naked flames and sparks, use flame proof equipment, work in a well ventilated area and keep out of reach of children.
Calculate your coverage
You will need:
Omega PoolKote 2 Pack Epoxy Pool Paint
4L m²)
Total coverage: 0 m²
This is an estimate only. Add 10% for wastage.
Technical Specifications
| Product Type | Two pack polyamide cured epoxy pool coating |
| Colours | Refer Poolkote colour chart - Aqua, Holly, Chamois, Coffee, Glazier, Pool Green, Pool Blue, Ocean Blue, Paradise Blue, Bright Blue, Bridge Grey, Jacaranda |
| Gloss Level | Semi gloss |
| Volume Solids | 49% |
| Mixing Ratio | 3:1 (Part A base to Part B hardener) |
| Pack Sizes | 4L and 20L kits |
| Theoretical Coverage | 9 m2 per litre |
| Coats | Minimum two coats, a third may be required to achieve the desired film thickness |
| Induction | Stand 5 minutes after mixing, stir 1 minute, then use immediately |
| Touch Dry | 2 hours @ 25C, 60% RH |
| Recoat | 24 hours @ 25C, 60% RH |
| Full Cure | 7 days @ 25C, 60% RH |
| Application Temperature | 15C to 30C, not in high humidity |
| Thinning | Omega Epoxy Thinner - 20% for the first coat on bare concrete, 5% for spray |
| Clean Up | Omega Epoxy Thinner |
| Shelf Life | 12 months minimum @ 25C, stored cool, dry and shaded |
| Density | 1.0 to 1.20 g/mL @ 25C (Part A)* |
| Flash Point | 27C (Part A)* |
| Boiling Point | 138C (Part A)* |
| Volatile Content | Greater than 50% w/w (Part A)* |
| GHS Classification | Flammable Liquids Category 3; Acute Toxicity Dermal Category 4; Acute Toxicity Inhalation Category 4; Skin Corrosion/Irritation Category 2; Serious Eye Damage/Irritation Category 2A; Skin Sensitisation Category 1A; STOT Single Exposure Category 3 |
| Dangerous Goods | UN 1263, PAINT, Class 3, Packing Group III, Hazchem +3[Y] |
| Scheduled Poison | S5 |
| * Typical values from the Part A Safety Data Sheet, Version 2, August 2023 | |
Frequently asked questions
-
How is PoolKote applied?
ApplicationMix Part B hardener with Part A base 3:1, stir thoroughly, let stand 5 minutes. Apply 2-3 coats by brush, roller or spray (spray needs 5% Omega Epoxy Thinner).
-
Which pool surfaces does it suit?
CompatibilityProperly prepared bare concrete (cured 28+ days) and fibreglass pools. Recoating of previously epoxy-painted concrete and fibreglass.
-
What is the coverage rate?
Coverage & Coats9 m²/L theoretical coverage. 4 L and 20 L kits available — surface profile affects practical coverage.
-
Dry times?
Cure & Dry TimeTouch dry 2 hours / recoat 24 hours / full cure 7 days at 25°C, 60% RH.
-
Shelf life and application limits?
Storage12 months minimum at 25°C. Do not apply when temperature is below 15°C or above 30°C, or in high humidity.
-
Is this product UV-stable above water?
PerformanceDesigned for underwater use only — direct sunlight exposure may cause fading, peeling or chalking. Apply Omega Omethane 343 topcoat if exposed sections are a concern.
Why trade professionals choose Omega
Omega supplies paints and protective coatings to the Australian trade, including the Rustblock range for corroded and bare metal. The line we carry covers the metalwork side of a waterproofing job: rust treatment and anti-corrosive metal priming, plus PoolKote two pack epoxy pool paint for pool shells. It is a small, practical range chosen for the jobs where steel and water meet.
Shop all OmegaMore from The Waterproofing Shop
Read up on the systems, or come and learn them hands on with our trainers.
